Cleaners
Cleaner 500
Cleaner 500 was developed to clean off certain heavy-duty cutting fluids and drawing compounds from steel and galvanized parts.
Cleaner 500 does not react with these compounds and thus allows total recovery and subsequent re-use of same. This process can save up to 50% of the lubricant cost.
Cleaner 500 also imparts some in-house rust protection with proper use.
Typical Data
Appearance: Straw coloured liquid
Odour: Mild
Specific Gravity: 1.01
pH Conc.: 9.5
pH 5% Solution: 8.9
Rust Test ASTM 4627/86: 12% No Rust
7% Solution: 1.0 Refractometer Reading
Application
Cleaner 500 is used at 5 – 10% in the first stage of cleaning lines as a spray cleaner between 120 – 180 o F (50 – 80 o C). The temperature can be varied depending on what has to be achieved.
a) 120 o F (50 o C) if oil emulsification is desired or if a bypass coalescer which flash heats the cleaning solution / oil emulsion to 160 – 180 oF (50 – 80 o C) to release the oil for reclaiming, is installed.
b) 160 – 180 o F (50 – 80 o C) if the oil is required to separate from the cleaner for reclaiming.
Reclaiming ideally is achieved with a proper capacity by-pass coalescer. For minimum contamination by Chloride (Cl – ) and Sulfate (SO 4 — ) ions and for maximum tank life and rust protection, it is recommended to use deionized water.
Cleaner 100LFC
Cleaner 100LFC is a general purpose heavy duty liquid cleaner for general shop, production and maintenance use.
Cleaner 100LFC is manufactured from the highest grade surfactants and solvents available today. It is completely biodegradable. The surfactants and solvents used are completely synthetic and have been specially selected to work well in both hard and soft waters. It will not develop hard water soap ‘curd’ and rinses freely and completely.
Cleaner 100LFC is an industrial strength cleaner and is compounded to be particularly efficient at cleaning severely soiled and oily surfaces such as machinery.
Cleaner 100LFC is used diluted with hot or cold water for general floor and wall cleaning. For more heavily soiled or oily surfaces, (machinery etc.), a dilution of 1 to 10 parts water is recommended. It may be applied by wiper, spray, brush, mop, etc. and is compatible with all paint and floor coverings in the diluted form.
| Application | Mixing Directions | Comments |
| Floors, wall, tiles, concrete, upholstery, all painted and hard surfaces. |
5% (Normal Dirt Load)
10% (Heavy Dirt Load) |
Wipe on, wipe off.
Wipe on, allow to soak |
| Production Machinery | From 10% to full strength. |
Apply and allow to soak for 10 – 15 min. Wipe or flush off. |
| Production Parts | From 10% to full strength. |
Dip, spray or wipe on. Apply warm for quick dry. |
5% = 8 oz. (about one cup) per gallon = 50 mls. per litre
10% = 16 ozs. (about two cups) per gallon = 100 mls. per litre.
Cleaner 100S
Cleaner 100S is a general purpose heavy duty liquid cleaner, which has a rust inhibitor incorporated into it. It is designed for general shop, production and maintenance use.
Cleaner 100S is manufactured from the highest grade surfactants and solvents available today. The surfactants and solvents used are completely synthetic and have been specially selected to work well in both hard and soft waters. Cleaner 100S will not develop hard water soap ‘curd’.
Cleaner 100S can be diluted with hot or cold water and may be applied by wiper, spray, brush, mop, etc. It is compatible with all paint and floor coverings in the diluted form.
| Application | Mixing Directions | Comments |
| Production Machinery | From 10% to full strength. |
Apply and allow to soak for 10 – 15 min. Wipe or flush off. |
| Production Parts | From 10% to full strength. |
Dip, spray or wipe on. Apply warm for quick dry. |
5% = 8 oz. (about one cup) per gallon = 50 mls. per litre
10% = 16 ozs. (about two cups) per gallon = 100 mls. per litre
Cleaner 100LFS = is a Low Foam Version
Cleaner 100 & 100LF
Cleaner 100 & 100LF are general purpose heavy duty liquid cleaners for general shop, production and maintenance use.
Cleaner 100 & 100LF are manufactured from the highest grade surfactants and solvents available today. They are completely biodegradable. The surfactants and solvents used are completely synthetic and have been specially selected to work well in both hard and soft waters. Cleaner 100 and 100LF will not develop hard water soap ‘curd’ and rinses freely and completely.
Cleaner 100 & 100LF are an industrial strength cleaner and are compounded to be particularly efficient at cleaning severely soiled and oily surfaces such as machinery.
Cleaner 100 & 100LF are used diluted with hot or cold water for general floor and wall cleaning. For more heavily soiled or oily surfaces, (machinery etc.), a dilution of 1 to 10 parts water is recommended. It may be applied by wiper, spray, brush, mop, etc. and is compatible with all paint and floor coverings in the diluted form.
| Application | Mixing Directions | Comments |
| Floors, wall, tiles, concrete, upholstery, all painted and hard surfaces. |
5% (Normal Dirt Load)
10% (Heavy Dirt Load) |
Wipe on, wipe off.
Wipe on, allow to soak |
| Production Machinery | From 10% to full strength. |
Apply and allow to soak for 10 – 15 min. Wipe or flush off. |
| Production Parts | From 10% to full strength. |
Dip, spray or wipe on. Apply warm for quick dry. |
5% = 8 oz. (about one cup) per gallon = 50 mls. per litre
10% = 16 ozs. (about two cups) per gallon = 100 mls. per litre
Cleaner 100LF = Cleaner 100 Low Foam Version